Honda NT650 Owner'S Manual Download Page 26 | Manualshive

Page: 26 / 97

background image

20

CLUTCH

Clutch  adjustment  may  be  required  if  the
motorcycle  stalls  when  shifting  into  gear
or  tends  to  creep;  or  if  the  clutch  slips,
causing acceleration to lag behind engine
speed.

Minor adjustments can be made with the
clutch cable adjuster (4) at the lever.
Normal clutch lever free play is: 10-20mm
(3/8-3/4 in)

(1) Clutch lever

Pull  back  the  rubber  dust  cover  (2).
Loosen  the  lock  nut  (3)  and  turn  the
adjuster (4). Tighten the lock nut (3) and
check  the  adjustment.  If  the  adjuster  is
threaded out near its limit or if the correct
free  play  cannot  be  obtained,  loosen  the
lock nut (3) and turn in the cable adjuster
(4)  completely.  Tighten  the  lock  nut  (3)
and pull on the dust cover.

(2) Dust cover
(3) Lock nut
(4) Clutch cable
adjuster

(A)

Increase free play

(B)

Decrease free play

«
...
24
25
26
27
28
...
»

Summary of Contents for NT650


































































































Reviews:

No comments

Related manuals for NT650

Brand: Kabuto Pages: 25

Brand: GAS GAS Pages: 57

Brand: R&G Pages: 13

Brand: Würth Pages: 188

Brand: GPX Pages: 44

Brand: Bosch Pages: 160

DARK SMOKE SPORT

Brand: Malossi Pages: 4

Brand: RIEJU Pages: 280

Brand: Ermax Pages: 2

Brand: Shark Pages: 24

Brand: O'Neal Pages: 12

Brand: Artago Pages: 4

Brand: Knight Pages: 19

FBG-P-RAN-09-XP

Brand: SuperATV Pages: 4

QUASAR 125 2003

Brand: APRILIA Pages: 168

Brand: KTM Pages: 12

Brand: KTM Pages: 50

Brand: KTM Pages: 129

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands