Honda MSX GROM 2020 Owner'S Manual Download Page 74

Page: 74 / 102

Loosen the upper lock nut and turn the

upper clutch cable adjuster all the way in

(to provide maximum freeplay). Tighten

the upper lock nut.

Loosen the lower lock nut.

Turn the lower clutch cable adjusting nut

until the clutch lever freeplay is 10 - 20

mm (0.4 - 0.8 in).

Tighten the lower lock nut and check the

clutch lever freeplay.

Start the engine, pull the clutch lever in,

and shift into gear. Make sure the engine

does not stall and the vehicle does not

creep. Gradually release the clutch lever

and open the throttle. Your vehicle should

move smoothly and accelerate gradually.

If proper adjustment cannot be obtained or

the clutch does not work correctly, see your

dealer.

20200817160140_32K26J100_eng_BOOK Page 72 Monday, August 17 2020 16:04:26 JST

Clutch

Adjusting the Clutch Lever Freeplay

Maintenance

Lower lock nut

Lower clutch cable

adjusting nut

–

Summary of Contents for MSX GROM 2020







































































































Search results

Summary of Contents for MSX GROM 2020

Reviews:

Related manuals for MSX GROM 2020

Brands by name

Popular brands

Honda MSX GROM 2020, Owner'S Manual

Search results

Summary of Contents for MSX GROM 2020

Reviews:

Related manuals for MSX GROM 2020

Brands by name

Popular brands