Honda MSX GROM 2020 Owner'S Manual Download Page 63

Page: 63 / 102

Removing & Installing Body Components

Battery

Removal

Make sure the ignition switch is in the

(Off) position.

Remove the seat.

P. 59

Remove the battery holder by removing the

bolt.

Disconnect the negative

terminal from

the battery.

Disconnect the positive

terminal from

the battery.

Remove the battery taking care not to

drop the terminal nuts.

Installation

Install the parts in the reverse order of
removal. Always connect the positive

terminal first. Make sure that bolts and nuts

are tight.

Make sure the clock information is correct

after the battery is reconnected.

P. 25

For proper handling of the battery, see

“Maintenance Fundamentals.”

P. 49

“Battery Goes Dead.”

P. 76

20200817160140_32K26J100_eng_BOOK Page 61 Monday, August 17 2020 16:04:26 JST

Maintenance

Battery holder
Positive terminal

Negative terminal

Battery

Bolt

Summary of Contents for MSX GROM 2020







































































































Search results

Summary of Contents for MSX GROM 2020

Reviews:

Related manuals for MSX GROM 2020

Brands by name

Popular brands

Honda MSX GROM 2020, Owner'S Manual

Search results

Summary of Contents for MSX GROM 2020

Reviews:

Related manuals for MSX GROM 2020

Brands by name

Popular brands