Honda MSX GROM 2020 Owner'S Manual Download Page 58

Page: 58 / 102

If the chain does not move smoothly, makes

strange noises, has damaged rollers, has loose

pins, or kinks, have the chain inspected by your

dealer.

Also inspect the drive sprocket and driven

sprocket. If either has worn or damaged teeth,

have the sprocket replaced by your dealer.

NOTICE

Use of a new chain with worn sprockets will cause

rapid chain wear.

Cleaning and Lubricating

After inspecting the slack, clean the chain and

sprockets while rotating the rear wheel. Use a

dry cloth with high flash-point solvent. Use a

soft brush if the chain is dirty.

After cleaning, wipe dry and lubricate with the

recommended lubricant.

Recommended lubricant:

Drive chain lubricant

If not available, use SAE 80 or 90 gear

oil.

Never use petrol or low flash point solvents for

cleaning the drive chain.

A fire or explosion could result.

20200817160140_32K26J100_eng_BOOK Page 56 Monday, August 17 2020 16:04:26 JST

Maintenance Fundamentals

Maintenance

Continued

Normal

(GOOD)

Worn

(REPLACE)

Damaged

(REPLACE)

Summary of Contents for MSX GROM 2020







































































































Search results

Summary of Contents for MSX GROM 2020

Reviews:

Related manuals for MSX GROM 2020

Brands by name

Popular brands

Honda MSX GROM 2020, Owner'S Manual

Search results

Summary of Contents for MSX GROM 2020

Reviews:

Related manuals for MSX GROM 2020

Brands by name

Popular brands