background image

44

SERVICING YOUR GENERATOR

MAINTENANCE SAFETY

Some of the most important safety precautions follow. However, we 
cannot warn you of every conceivable hazard that can arise in 
performing maintenance. Only you can decide whether or not you 
should perform a given task.

Safety Precautions

Make sure the engine is off before you begin any maintenance or 
repairs. This will eliminate several potential hazards:

– Carbon monoxide poisoning from engine exhaust.

Operate outside away from open windows or doors.

– Burns from hot parts.

Let the engine and exhaust system cool before touching.

– Injury from moving parts.

Do not run the engine unless instructed to do so.

• Read the instructions before you begin, and make sure you have the 

tools and skills required.

• To reduce the possibility of fire or explosion, be careful when 

working around gasoline. Use only a non-flammable solvent, not 
gasoline, to clean parts. Keep cigarettes, sparks, and flames away 
from all fuel-related parts.

Improper maintenance can cause 
an unsafe condition.

Failure to properly follow 
maintenance instructions and 
precautions can cause serious 
injuries or death.

Always follow the procedures and 
precautions in this owner's manual.

32Z446000.book  Page 44  Friday, February 2, 2018  3:46 PM

Summary of Contents for EU22i











































































Reviews: