Honda EU22i Owner'S Manual Download | Manualshive

Page: 48 / 74

background image

46

SERVICING YOUR GENERATOR

REFUELING

With the engine stopped, remove the fuel filler cap and check the fuel
level. Refill the fuel tank if the fuel level is low.

Fuel can damage paint and plastic. Be careful not to spill fuel when
filling your fuel tank. Damage caused by spilled fuel is not covered
under warranty.

Refuel in a well-ventilated area before starting the engine. If the engine
has been running, allow it to cool. Refuel carefully to avoid spilling fuel.
Do not fill the fuel tank above the upper level mark (see page 47) on the
fuel filter.

Never refuel the engine inside a building where gasoline fumes may
reach flames or sparks. Keep gasoline away from appliance pilot lights,
barbecues, electric appliances, power tools, etc.

Spilled fuel is not only a fire hazard, it causes environmental damage.
Wipe up spills immediately.

Gasoline is highly flammable and
explosive.

You can be burned or seriously
injured when handling fuel.

• Stop the engine and let it cool

before handling fuel.

• Keep heat, sparks, and flame away.
• Handle fuel only outdoors.
• Wipe up spills immediately.

32Z446000.book Page 46 Friday, February 2, 2018 3:46 PM

«
...
46
47
48
49
50
...
»

Summary of Contents for EU22i











































































Reviews:

No comments

Related manuals for EU22i

Brand: Midian Pages: 28

Brand: GE Pages: 55

COMBIVERT F5 Series

Brand: KEB Pages: 116

Brand: Perle Pages: 23

Brand: TIE Pages: 4

Brand: Hamron Pages: 28

Pro Enigma MI-X450

Brand: Aiwa Pages: 13

Brand: AV Link Pages: 2

Brand: Metra Electronics Pages: 9

Brand: AGM Pages: 71

Brand: MRC Pages: 2

Brand: Emheater Pages: 30

PerfectPower PP1000

Brand: Waeco Pages: 88

AMX N2400 Series

Brand: Harman Pages: 80

Brand: PhD Solutions Pages: 14

CoolSET ICE2QR 65 Series

Brand: Infineon Pages: 24

blueplanet XP10U-H4 PSD

Brand: Kaco Pages: 53

Brand: Zipper Mowers Pages: 92

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands