Honda EU22i Owner'S Manual Download

Page: 57 / 74

SERVICING YOUR GENERATOR

5. Inspect the spark plug. Replace it

if the electrodes are worn or if
the insulator is cracked, chipped,
or fouled.

6. Measure the spark plug

electrode gap with a wire-type
feeler gauge. Correct the gap, if
necessary, by carefully bending
the side electrode.

The gap should be:
0.6–0.7 mm

7. Make sure that the spark plug sealing washer is in good condition,

and thread the spark plug in by hand to prevent cross-threading.

8. After the spark plug is seated, tighten with a spark plug wrench to

compress the sealing washer.

If reinstalling a used spark plug, tighten 1/8–1/4 turn after the spark
plug seats.
If installing a new spark plug, tighten 1/2 turn after the spark plug
seats.

TORQUE

: 12 N·m, 1.2 kgf·m

A loose spark plug can overheat and damage the engine.
Overtightening the spark plug can damage the threads in the
cylinder head.

9. Reinstall the spark plug cap on the spark plug securely.

10. Reinstall the spark plug maintenance cover.

SIDE ELECTRODE

SEALING WASHER

0.6–0.7 mm

INSULATOR

32Z446000.book Page 55 Friday, February 2, 2018 3:46 PM

Summary of Contents for EU22i











































































Search results

Summary of Contents for EU22i

Reviews:

Related manuals for EU22i

Brands by name

Popular brands

Honda EU22i, Owner'S Manual

Search results

Summary of Contents for EU22i

Reviews:

Related manuals for EU22i

Brands by name

Popular brands