manualshive.com logo in svg

Honda EU22i, Owner'S Manual

Share
Download
Honda EU22i Owner'S Manual Download Page 34

32

OPERATION

2. Connect the cable connectors and ground terminals of the 

receptacle box for parallel operation to the generators and secure 
the cord clamp to handle.

• Place two generators at least 1 meter away from each other 

during parallel operation.

• Route the wire through the handle and clamp it to the handle 

using the band.

• Take care not to slacken the wire toward the starter grip side.
• Connect the longer wire to the generator on which the receptacle 

box for parallel operation is not installed.

• Do not set the generators with the exhaust side face to face each 

other.

3. Connect the ground terminal of one generator to the ground.

• When an appliance is connected to the ground, connect the 

generator to the ground as well.

PARALLEL OPERATION OUTLETS
(optional equipment)

GROUND
TERMINAL

BAND

At least 1 m

32Z446000.book  Page 32  Friday, February 2, 2018  3:46 PM

Summary of Contents for EU22i











































































Reviews:

No comments

Brands by name

Popular brands

Load more brands