Honda EU2000i Companion Owner'S Manual Download Page 18 | Manualshive

Page: 18 / 75

background image

16

AC CIRCUIT PROTECTOR

DC RECEPTACLE

DC CIRCUIT PROTECTOR

PUSH

AC CIRCUIT PROTECTOR

AC RECEPTACLES

AC CIRCUIT PROTECTOR

ON

OFF

ON

OFF

DC CIRCUIT PROTECTOR

DC RECEPTACLE

PUSH

The AC circuit protector will automatically switch OFF if there is a short
circuit or a significant overload of the generator at the AC receptacles.
If the circuit protector switches OFF automatically, check that the
appliance is working properly and does not exceed the rated load
capacity of the circuit before resetting the circuit protector ON.

The DC circuit protector automatically shuts off the DC battery
charging circuit when the DC charging circuit is overloaded, when
there is a problem with the battery, or when the connections between
the battery and the generator are improper.

The DC receptacle should ONLY be used for charging 12-volt
automotive type batteries. The DC charging output is not regulated.

06/12/21 09:17:33 31Z07602_017

«
...
16
17
18
19
20
...
»

Summary of Contents for EU2000i Companion












































































Reviews:

No comments

Related manuals for EU2000i Companion

AWPH360N - PAN/TILT HEAD

Brand: Panasonic Pages: 48

Brand: IBS Pages: 24

Brand: Panasonic Pages: 1

Brand: Bang & Olufsen Pages: 12

Brand: SALSA Pages: 2

BEA LZR-WIDESCAN

Brand: Halma Pages: 12

Brand: Hama Pages: 6

Brand: Hama Pages: 2

HOIST-A-TOP JL CRANK

Brand: Lange Originals Pages: 13

Brand: OFFCARR Pages: 12

Brand: OEM Tools Pages: 4

Brand: KEDO Pages: 2

Brand: KEDO Pages: 3

Brand: KEDO Pages: 2

Brand: HBM Pages: 40

Brand: DÖRR Pages: 24

Brand: Torklift Pages: 16

Brand: Woom Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands