Honda EU2000i Companion Owner'S Manual Download Page 48 | Manualshive

Page: 48 / 75

background image

46

SPARK PLUG SERVICE

Recommended spark plug:

SPARK PLUG
MAINTENANCE
COVER

SPARK PLUG CAP

SPARK PLUG WRENCH

SPARK PLUG CAP

In order to service the spark plug, you will need a spark plug wrench
(commercially available).

To ensure proper engine operation, the spark plug must be properly
gapped and free of deposits.

An incorrect spark plug can cause engine damage.

Remove the spark plug maintenance cover.

Use a spark plug wrench to remove the spark plug.

Remove the spark plug cap.

Clean any dirt from around the spark plug base.

CR5HSB (NGK)

If the engine has been running, allow it to cool before servicing the
spark plug.

1.

2.

3.

4.

06/12/21 09:20:53 31Z07602_047

«
...
46
47
48
49
50
...
»

Summary of Contents for EU2000i Companion












































































Reviews:

No comments

Related manuals for EU2000i Companion

Brand: Calumet Pages: 4

Brand: Garland Pages: 36

Brand: 4MOMS Pages: 20

Brand: Hach Pages: 42

Brand: Hach Pages: 36

Brand: Jetter Pages: 4

Brand: K&K Pages: 8

Brand: K&K Pages: 20

Brand: K&K Pages: 6

Brand: K&K Pages: 3

Brand: K&K Pages: 3

Brand: Sanitas Pages: 52

Brand: Unimig Pages: 16

WorkCentre Pro 123

Brand: Xerox Pages: 4

Brand: Hobo Pages: 7

Brand: M2M Pages: 20

Brand: Oki Pages: 20

Brand: Yoshimura Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands