Honda EU2000i Companion Owner'S Manual Download Page 26

Page: 26 / 75

−

＋

−

DC OPERATION

Connecting the battery charging cable (optional equipment):

The battery gives off explosive gases; keep sparks, flames and
cigarettes away. Provide adequate ventilation when charging or using
batteries.

WARNING:

Wash hands after handling.

PUSH

OFF

DC CIRCUIT PROTECTOR

DC RECEPTACLE

When using the DC output, turn the Eco-Throttle switch to the OFF
position.

Before connecting the battery charging cable to a battery that is
installed in a vehicle, disconnect the vehicle battery ground cable
from the negative (

) battery terminal.

The DC receptacle should ONLY be used for charging 12-volt
automotive type batteries. The DC charging output is not regulated.

Start the generator.

Connect the red lead of the battery charging cable to the positive
(

) battery terminal and the black lead to the negative (

) battery

terminal.

Plug the battery charging cable into the DC receptacle of the
generator.

Battery posts, terminals and related accessories contain

lead and lead components.

06/12/21 09:13:37 31Z07602_025

Summary of Contents for EU2000i Companion












































































Search results

Summary of Contents for EU2000i Companion

Reviews:

Related manuals for EU2000i Companion

Brands by name

Popular brands

Honda EU2000i Companion, Owner'S Manual

Search results

Summary of Contents for EU2000i Companion

Reviews:

Related manuals for EU2000i Companion

Brands by name

Popular brands