Honda 08E91-E22-100A Installation Instructions Manual Download Page 10

Page: 10 / 24

10 of 24

AII 35365 (0708)

32. Secure the engine starter harness to the vehicle

harness with two wire ties in the areas shown.

33. Disconnect the vehicle 20-pin connector from the

TPMS control unit (removed in step 24), and plug it
into the engine starter harness 20-pin connector.
Plug the remaining engine starter harness 20-pin
connector into the TPMS control unit.

6D1817BY

VEHICLE

HARNESS

2 VEHICLE

CLIPS

ENGINE

STARTER

HARNESS

2 WIRE

TIES

WIRE TIE VEHICLE

HARNESS ENGINE

STARTER

HARNESS

Inside.

6D1818AY

VEHICLE 20-PIN

CONNECTOR

20-PIN

CONNECTOR

TPMS CONTROL

UNIT

VEHICLE 20-PIN

CONNECTOR

20-PIN

CONNECTOR

ENGINE STARTER

HARNESS

34. Align the green tape on the engine starter harness

with the clip on the vehicle harness, and secure the
engine starter harness to the vehicle harness with
one wire tie.

35. Near the connector, secure the engine starter

harness to the vehicle harness with one wire tie.

36. Secure the engine starter harness to the vehicle

harness with two long wire ties at the locations
shown.

6D1811AY

VEHICLE

HARNESS

ENGINE

STARTER

HARNESS

WIRE TIE

VEHICLE

CLIP

GREEN

TAPE

6D1819EY

ENGINE STARTER

HARNESS

VEHICLE

HARNESS

WIRE TIE

VEHICLE

HARNESS

LONG WIRE

TIES

CONNECTOR

Summary of Contents for 08E91-E22-100A

























Search results

Summary of Contents for 08E91-E22-100A

Reviews:

Related manuals for 08E91-E22-100A

Brands by name

Popular brands

Honda 08E91-E22-100A, Installation Instructions Manual

Search results

Summary of Contents for 08E91-E22-100A

Reviews:

Related manuals for 08E91-E22-100A

Brands by name

Popular brands