Honda 08E91-E22-100A Installation Instructions Manual Download Page 11

Page: 11 / 24

AII 35365 (0708)

11 of 24

37. Reinstall the TPMS control unit to the vehicle bracket

using the vehicle bolt removed in step 24.

38. Route the engine starter harness along the vehicle

harness to the front of the fuse box.

39. Loosely attach the engine starter harness to the

vehicle harness with one wire tie.

721503AY

VEHICLE

BRACKET

VEHICLE

UNIT

TPMS CONTROL

BOLT

Removed in step 24.

6D1820AY

WIRE TIE

(Loosely attach.)

FUSE BOX

ENGINE

STARTER

HARNESS

VEHICLE

HARNESS

40. Disconnect the vehicle 5-pin connector from the fuse

box. Plug the engine starter harness 5-pin connector
into the fuse box 5-pin connector. Wrap one
urethane tape around the vehicle 5-pin connector.
NOTE:

Check that the engine starter harness 5-pin

connector is connected to the vehicle connector and
locked securely. A loose connector can cause
engine to stall.

6D1823DY

FUSE

BOX

VEHICLE

5-PIN

CONNECTOR

5-PIN

CONNECTOR

Unlock connector

VEHICLE

5-PIN

CONNECTOR

Push.

Pull.

Push.

ENGINE STARTER

HARNESS

URETHANE

TAPE

Lock connector

Push.

Lock connector

Push.

Summary of Contents for 08E91-E22-100A

























Search results

Summary of Contents for 08E91-E22-100A

Reviews:

Related manuals for 08E91-E22-100A

Brands by name

Popular brands

Honda 08E91-E22-100A, Installation Instructions Manual

Search results

Summary of Contents for 08E91-E22-100A

Reviews:

Related manuals for 08E91-E22-100A

Brands by name

Popular brands