Holtek HT66F488 Manual Download Page 93

Page: 93 / 195

Rev. 1.21

�2

�ove��e� �� 2�1�

Rev. 1.21

�3

�ove��e� �� 2�1�

HT66F488/HT66F489

A/D Flash MCU with EEPROM

HT66F488/HT66F489

A/D Flash MCU with EEPROM

different from the initial value setup using the PTnOC bit otherwise no change will

occur on the TM output pin when a compare match occurs. After the TM output pin

changes state it can be reset to its initial level by changing the level of the PTnON bit

from low to high.

Bit 3

PTnOC

: PTPn Output control bit

Compare Match Output Mode

0: Initial low

1: Initial high

PWM Mode/Single Pulse Output Mode

0: Active low

1: Active high

This is the output control bit for the TM output pin. Its operation depends upon

whether TM is being used in the Compare Match Output Mode or in the PWM Mode/

Single Pulse Output Mode. It has no effect if the TM is in the Timer/Counter Mode. In

the Compare Match Output Mode it determines the logic level of the TM output pin

before a compare match occurs. In the PWM Mode it determines if the PWM signal is

active high or active low.

Bit 2

PTnPOL

: PTPn Output polarity control

0: Non-invert

1: Invert

This bit controls the polarity of the PTPn output pin. When the bit is set high the TM

output pin will be inverted and not inverted when the bit is zero. It has no effect if the

TM is in theTimer/Counter Mode.

Bit 1

PTnCKS

: Input Capture trigger source selection

0: External Clock source of Capture Input Mode comes from PTPn

1: External Clock source of Capture Input Mode comes from PTCKn

Bit 0

PTnCCLR

: Select PTMn Counter clear condition

0: PTMn Comparator P match

1: PTMn Comparator A match

This bit is used to select the method which clears the counter. Remember that the P-type

TM contains two comparators, Comparator A and Comparator P, either of which can

be selected to clear the internal counter. With the PTnCCLR bit set high, the counter

will be cleared when a compare match occurs from the Comparator A. When the bit is

low, the counter will be cleared when a compare match occurs from the Comparator

P or with a counter overflow. A counter overflow clearing method can only be

implemented if the CCRP bits are all cleared to zero. The PTnCCLR bit is not used in

the PWM, Single Pulse or Input Capture Mode.

Summary of Contents for HT66F488




































































































































































































Search results

Summary of Contents for HT66F488

Reviews:

Holtek HT66F488, Manual, Page: 93 / 195

Search results

Summary of Contents for HT66F488

Reviews: