background image

Doorphone Adjustments and Programming 

Page 6

TYPE 115

In certain noisy locations (traffic or wind), the microphone volume may need to be decreased. A symptom
of  this is one-way talk path, in which the distant party cannot be heard over the speaker. A “

MIC VOL

adjustment is provided on the doorphone for increasing or decreasing the microphone volume.

Microphone Volume

The “

SPKR VOL

” pot can be adjusted to increase or decrease the speaker volume to the desired level.

Speaker Volume

The “

maximum number of rings can be adjusted using the DIP switches.

Maximum Number of Rings

Sw 1    Sw 2    Max Rings

OFF     OFF          2

ON      OFF          3

OFF      ON           10

ON       ON           30

1

Disconnect the PHONE LINE INPUT.

2

Slide the TALK BATTERY switch to the ON position.

3

Move DIP SWITCH 2 from OFF to ON.

4

Connect a phone to terminals 4 & 5 -  LINE OUT TO PHONES.

5

Pick up the phone (you will hear a double beep - indicating that you have accessed the PROGRAMMING MODE).

6

You can now Touch Tone program the features listed below

Access Programming Mode (Local Access)

Step

Action

1

Make sure C-1000B is in Programmin Mode - See above

2

Program Strike 1 activation time as follows:

3

Enter time (seconds) followed by #01

4

Program Strike 2 activation time as follows:

5

Enter time (seconds) followed by #02
EXAMPLE:  05#01 programs  Strike 1 for 5 seoncds

03#02 programs  Strike 2 for 3 seconds

Program Gate Strike Relays

Step

Action

NOTE: Entering a time “00” sets time = 1/2 second Maximum time through programming = 9 seconds 

Summary of Contents for 101-VIK













Reviews: