manualshive.com logo in svg

Hologic TLi IQ, User Manual

Share
Download
Hologic TLi IQ User Manual Download Page 30

 

TLi

IQ

 System User Manual  

 

1 – 19 

Section 1 – Introduction

 

CAUTIONS AND WARNINGS

 

 
There are no known hazards associated with the TLi

IQ

 System when it is operated in accordance with the instructions in 

this manual. However, you should be aware of situations that can result in serious injury. 
 

WARNING!

  Ensure that the analyzer power adapter is connected to a grounded AC electrical outlet that 

provides voltage and current specified by Hologic. Use of an incompatible power receptacle can cause shock 
and fire hazard. 

 
CAUTION!

  Use only the power adapter supplied by Hologic. Use of an incompatible power adapter can damage the 

internal components.

 

 
CAUTION!

  Always turn off the power and unplug the power adapter before cleaning the exterior of the analyzer. Fluid 

can damage internal components. DO NOT clean the power adapter. 
 

CAUTION!

  Extreme heat can damage the display and other electronic components. 

 

Summary of Contents for TLi IQ










































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands