Hobbico Mini Switch Instruction Manual Download Page 9

Page: 9 / 24

❏

6. Connect the Y-harness to the aileron servo leads. Test

fi t the low wing confi guration canopy hatch to the fuselage
and screw it in place.

NOTE:

The low wing confi guration

will require you to readjust your control surface trims.

Be prepared

for this on your fi rst fl ight.

❏

7. Move the clevis to the innermost hole in the rudder

control horn. The additional rudder movement will improve
performance in the low wing confi guration. Be sure to move
the clevis back to the outer hole if returning to the high wing
confi guration.

GET THE MODEL READY TO FLY

Prepare the Transmitter

and LiPo Battery

❏

1. Install fresh AA batteries into the transmitter. Follow

the diagram molded inside the battery compartment.

❏

2. Familiarize yourself with the charging procedure of the

included LiPo battery. Read the charger manual completely.

❏

3. Fully charge the LiPo battery.

❏

4. Test fi t the battery in the airplane. The battery wires

should be tucked neatly along the side of the battery.

Lithium Battery Handling & Usage

WARNING!!

Read the entire instruction sheet included with

the battery. Failure to follow all instructions could cause
permanent damage to the battery and its surroundings, and
cause bodily harm!

●

ONLY

use a LiPo approved charger.

NEVER

use

a NiCd/NiMH peak charger!

●

NEVER

charge in excess of 4.20V per cell.

●

ONLY

charge through the “charge” lead.

NEVER

charge through the “discharge” lead.

●

NEVER

charge at currents greater than 1C.

●

ALWAYS

set charger’s output volts to match

battery volts.

●

ALWAYS

charge in a fi re proof location.

●

NEVER

trickle charge.

●

NEVER

allow battery temperature to exceed

150°F (65°C).

●

NEVER

disassemble or modify pack wiring in any

way or puncture cells.

Summary of Contents for Mini Switch

























Search results

Summary of Contents for Mini Switch

Reviews:

Related manuals for Mini Switch

Brands by name

Popular brands

Hobbico Mini Switch, Instruction Manual

Search results

Summary of Contents for Mini Switch

Reviews:

Related manuals for Mini Switch

Brands by name

Popular brands