manualshive.com logo in svg

Hobbico Mini Switch, Instruction Manual

Share
Download
Hobbico Mini Switch Instruction Manual Download Page 10

10

●

  

NEVER

 discharge below 2.75V per cell.

●

  

NEVER

 place on combustible materials or leave 

unattended during charge or discharge.

●

  

ALWAYS KEEP OUT OF REACH OF CHILDREN

.

Check the Control Directions

❏ 

1. 

 

With the battery fully charged, turn on your 

transmitter and move the throttle stick (left stick) down 
to the idle position. Then, plug the motor battery into the 
ESC. If the ESC makes an erratic pattern of beeps after the 
initial startup beeps and a few seconds of silence, then it 
has entered programming mode and the throttle channel 
needs to be reversed on the transmitter, following Step 2. 
If not, skip Step 2. 

Take care around the propeller! The 

propeller will rotate when the throttle is advanced.

(Complete ESC programming instructions are included on 

page 15 of this manual)

 

❏ 

2.  Disconnect the battery from the ESC. Then, move the 

throttle reversing switch on the transmitter. Confi rm that the 
throttle stick is still in the idle position and reconnect the 
battery to the ESC.

FULL

THROTTLE

RUDDER

MOVES

RIGHT

ELEVATOR

MOVES DOWN

RIGHT AILERON

MOVES UP

LEFT AILERON

MOVES DOWN

4-CHANNEL RADIO SETUP 

(STANDARD MODE 2)

 

❏ 

3.  View the model from behind and move the rudder 

control (left stick) on the transmitter to the left. The rudder 
should move to the left. If not, move the rudder reversing 
switch on the transmitter and then test the operation of the 
rudder again.

 

❏ 

4.  Moving the elevator control down (right stick) should 

cause the elevator to move up. Flip the elevator reversing 
switch on the transmitter if necessary.

 

❏ 

5.  Moving the aileron control to the right (right stick) 

should cause the left aileron to move down and the right 
aileron to move up. Flip the aileron reversing switch on the 
transmitter if necessary.

Summary of Contents for Mini Switch

























Reviews:

No comments

Brands by name

Popular brands

Load more brands