HNP Mikrosysteme mzr-2961 Operating Manual Download

Page: 47 / 58

EC-manufacturer’s certificate

(following Machinery Directive 2006/42/EU)

We hereby declare that the following micro annular gear pump of the magnetic

hermetic series:

mzr-2961, mzr-4661

are intended for installation into another machinery/plant and that start of

operation is forbidden until it is identified that the machinery/plant into which

these micro annular gear pumps shall be installed corresponds to the

regulations of the EC guidelines regarding safety and health requirements.

We confirm the conformity of the product described above to the following

standards in terms of applied directives

−

Machinery Directive (2006/42/EU)

Applied standards are particularly

DIN EN 809

DIN EN 60204-1

DIN EN 294

DIN EN ISO 12100 part 1

DIN EN 953

DIN EN ISO 12100 part 2

UVV

This statement does not warrant any characteristics in terms of product liability.

Please note the safety instructions in the manual.

Mr. Lutz Nowotka, HNP Mikrosysteme GmbH, Bleicherufer 25, D-19053

Schwerin is authorised to compile the technical file according to Annex VII A.

Date: 17 May 2013
Signature manufacturer:

Dr. Thomas Weisener

CEO

Summary of Contents for mzr-2961



























































Search results

Summary of Contents for mzr-2961

Reviews:

Related manuals for mzr-2961

Brands by name

Popular brands

HNP Mikrosysteme mzr-2961, Operating Manual

Search results

Summary of Contents for mzr-2961

Reviews:

Related manuals for mzr-2961

Brands by name

Popular brands