HNP Mikrosysteme mzr-2961 Operating Manual Download

Page: 32 / 58

7 Start Up / Shut Down

Operation manual mzr-2961, mzr-4661

Technical data subject to change without prior notice!

Last update: April 2018

Nature of the handled liquid

Flushing cycle
[min]

Suitable flushing liquid

Oils, fats, plastifiers

15-20

isopropanol, ethanol, acetone, benzine

Solvents (polar + nonpolar)

5-10

isopropanol, ethanol

Other organic liquids

10-15

isopropanol , ethanol

Refrigerating and cooling agents

15-20

isopropanol, ethanol

Neutral watery solutions

20-25

isopropanol, ethanol

Basic solutions

25-30

DI-water (deionized water)

Organic acids

30-40

isopropanol, ethanol

Weak mineral acids

25-30

DI- water

Strong mineral acids

35-45

DI- water

Strong oxidizing liquids

35-45

DI- water

Paints, varnishes, adhesives

50-60

Not specified - for further information
please contact HNP Mikrosysteme.

table 9

Selection of the flushing liquid (solvent) and the duration of the flushing cycle depending on the delivered
liquid.

Warning

Please make sure that the pump components and particularly O-rings and

sealing are resistant to the employed flushing liquid (see table 10).

Shaft sealing

O-ring material

Flushing liquid

PTFE (Teflon

graphite-

reinforced

UHMWPE

FPM

(Viton

)

EPDM

FFPM

acetone

benzene

benzyl alcohol

benzine

butanol

dimethyl sulfoxide (DMSO)

ethanol

isopropanol

methanol

methylethylketone (MEK)

oil / fine mechanics oil

styrene

toluene

water

xylene

Legend:

0 ... good suitability 1 ... suitability 2 ... conditional suitability 3 ... labile - ... not specified

table 10

Resistance of the sealing materials depending on the flushing liquid (solvent)

Summary of Contents for mzr-2961



























































Search results

Summary of Contents for mzr-2961

Reviews:

Related manuals for mzr-2961

Brands by name

Popular brands

HNP Mikrosysteme mzr-2961, Operating Manual

Search results

Summary of Contents for mzr-2961

Reviews:

Related manuals for mzr-2961

Brands by name

Popular brands