HNP Mikrosysteme mzr-11507 Operation Manual Download

Page: 47 / 55

EC-manufacturer’s certificate

(following Machinery Directive 2006/42/EC)

We hereby declare that the following micro annular gear pump of the high

performance series:

mzr-11507

is intended for installation into another machinery/plant and that start of

operation is forbidden until it is identified that the machinery/plant into which

these micro annular gear pumps shall be installed corresponds to the

regulations of the EC guidelines regarding safety and health requirements.

We confirm the conformity of the product described above to the following

standards in terms of applied directives

−

Machinery Directive (2006/42/EC)

Applied standards are particularly

DIN EN 809

DIN EN 60204-1

DIN EN 294

DIN EN ISO 12100 part 1

DIN EN 953

DIN EN ISO 12100 part 2

UVV

This statement does not warrant any characteristics in terms of product liability.

Please note the safety instructions in the manual.

Mr. Lutz Nowotka, HNP Mikrosysteme GmbH, Bleicherufer 25, D-19053

Schwerin is authorised to compile the technical file according to Annex VII A.

Date: 30 December 2009
Signature manufacturer:

Dr. Thomas Weisener

CEO

Summary of Contents for mzr-11507
























































Search results

Summary of Contents for mzr-11507

Reviews:

Related manuals for mzr-11507

Brands by name

Popular brands

HNP Mikrosysteme mzr-11507, Operation Manual

Search results

Summary of Contents for mzr-11507

Reviews:

Related manuals for mzr-11507

Brands by name

Popular brands