HLF 4600 G1 Instruction Manual Download Page 27 | Manualshive

Page: 27 / 73

HLF 4600 G1 Instruction Manual Download Page 27

INSTALLATION

I.M. HLF 4600 G1/2/F Eng V2-2010

27

HLF Italian Design

3.2.6 Adjusting the Coffee Grinder

At this point of the initial start up, the HLF 4600 G coffee maker is ready to dispense the
first beverage and the factory recommend to start making a coffee in order to adjust the
grinder blades.

NOTE

The HLF 4600 G coffee maker arrives with the blades of the coffee grinder, almost
open in order to accept every kind of coffee beans used by the operator.

The reason of this factory action is to avoid any damage to the grinder motor, because
in presence of coffee beans too oily and with the blades position almost close, the
grinder motor can stop working.

The solution to this eventual problem is to start making a coffee with the blades almost
open and check that all the process works without troubles.

Push the

Espresso

button (n° 1) to start the coffee drink process. The message

Working…

will appear on the LCD display.

Working…

The grinder will start grinding the coffee beans, and after 7 - 8 seconds the coffee
dispenser will dump the coffee ground into the coffee group. This event is recognizable
by the sound of three “knock”.

The coffee group will now move from the stand-by position to the brewing position, and
the water pump will start to run.

At this point is important to watch the speed of the coffee coming out from the drink
nozzle into the cup, wondering if it’s coming out too fast or too slow (almost dripping).

If the speed of the coffee is fast and at the end of the brewing there is no brown coffee
cream on top of cup, it means that the grinder blades are too open and they need to be
closed.

«
...
25
26
27
28
29
...
»

Summary of Contents for 4600 G1










































































Reviews:

No comments