manualshive.com logo in svg

HLF 4600 G1, Instruction Manual, Page: 26 / 73

Share
Download
HLF 4600 G1 Instruction Manual Download Page 26

INSTALLATION 

 
I.M. HLF  4600 G1/2/F Eng V2-2010 

26 

 

HLF  Italian Design 

 

•

 

Put Empty Carafe Under Drink Nozz:

 The machine is asking for an empty 

carafe under the drink nozzle outlets. The carafe has to be at least 1,5 Litre 
capacious. 
 

•

 

Press Red Button: 

Once the carafe has been placed, press the CLEANING 

button to run the cleaning cycle. 

 
If during this process the message 

CAUTION Check Water

 appears, turn OFF the 

machine for 3 seconds and then back ON to reset the computer 
 

 
 
 

 

C A U T I O N  

Check Water 

Then re-start the cleaning cycle process, by pushing the CLEANING button again. 
 

 

NOTE

 

 
If the message 

Hold Red Button

 will not appear on the LCD display, run the cleaning 

cycle anyway, in order to make sure that all the hydraulic circuit is filled with water. 
Refer to paragraph 4 “Cleaning Guide”. 
 
 

3.2.5 Initial heating 

 
Once the cleaning cycle is finished, the message 

Wait for Heating

 will appear on the 

LCD display of the HLF  4600 G coffee maker. 
 

 

 

Wait for Heating 

 
 
 

 
The internal boiler is heating the water and this process is going to take around 5 
minutes. When the message 

Select a Drink

 will appear on the LCD display, the HLF  

4600 G coffee maker is ready to work. 
 

 
 
 

 

 

Select a Drink 

Close the front door and place your cup on the cup holder of the drip tray.  

Summary of Contents for 4600 G1










































































Reviews:

No comments