manualshive.com logo in svg

HLF 4600 G1, Instruction Manual, Page: 16 / 73

Share
Download
HLF 4600 G1 Instruction Manual Download Page 16

SAFETY INSTRUCTIONS 

 
I.M. HLF  4600 G1/2/F Eng V2-2010 

16 

 

HLF  Italian Design 

 

 CAUTION

 

 

 
• Only operate the HLF  4600 G coffee maker in covered locations, avoiding places 
where there is a risk of water splash. There is a risk of damage.  
 
• Never spray the HLF  4600 G coffee maker with a water hose during cleaning. There is 
a risk of damage.  
 
• Always empty the coffee grounds container correctly. There is a danger of overflow.  
 

 WARNING

  

 
If handled improperly, the equipment could cause serious or fatal injuries. Anyone using 
and maintaining the equipment must have knowledge of the correct handling of the 
equipment and must have read and understood the safety instructions in this 
Instructions Manual before starting to use or maintain the equipment.  
 

 WARNING

  

 
Never modify or remove any safety mechanisms. Do not disable any safety 
mechanisms by modifying the equipment. If there are any warning symbols affixed to 
the equipment, do not remove them. Replace any lost or defective warning symbols 
immediately.  
 

 WARNING 

 

 
Never operate the equipment in a damaged condition. Report any irregularities to your 
superior immediately, especially if they affect safety.  
 
 

Summary of Contents for 4600 G1










































































Reviews:

No comments