HLF Italian Design 1700 Service Manual Download Page 92

Page: 92 / 115

TROUBLESHOOTING

14.15 E72-CLEAN COFFEE GROUP

Why?

The machine has detected an unusual current consumption of the

coffee group

gearmotor

Cause of fault

Troubleshooting measure(s)

The

coffee group

is dirty.

Remove the

coffee group

and clean it

from the coffee.

Put some grease on the main screw and
O-Rings.

14.16 E73-FLASH MEMORY ERROR / E102-EEPROM WRITE ERROR
MOTHERBOARD

Why?

Error while saving data on the motherboard. Replace it.

14.17 E74-COFFEE GROUP TIMEOUT

Why?

The

coffee group

has taken too much time to finish a positioning than usual.

Cause of fault

Troubleshooting measure(s)

The

coffee group

wasn’t in the position

the machine expected.

Push on the notification to reset the
coffee group.

HLF Italian Design

14-12

S.M. HLF 1700 G1-F Eng V0-2016

Summary of Contents for 1700




















































































































Search results

Summary of Contents for 1700

Reviews:

Related manuals for 1700

Brands by name

Popular brands

HLF Italian Design 1700, Service Manual

Search results

Summary of Contents for 1700

Reviews:

Related manuals for 1700

Brands by name

Popular brands