HLF Italian Design 1700 Service Manual Download Page 95

Page: 95 / 115

TROUBLESHOOTING

14.22 E119-CHANGE GIVER INCOMPATIBLE

Why?

The change giver connected to the machine is not compatible to the current machine
settings.

Cause of fault

Troubleshooting measure(s)

The base coin of the change giver is
different than the one set into the
machine.

Check which base coin the change giver
uses (refer to the instruction manual of
the change giver) and make sure the
machine is using the same value.

14.23 E120-CASHLESS DEVICE INCOMPATIBLE

Why?

The cashless device connected to the machine is not compatible to the current machine
settings.

Cause of fault

Troubleshooting measure(s)

The base coin of the cashless device is
different than the one set into the
machine.

Check which base coin the cashless
device uses (refer to the instruction
manual of the cashless device) and
make sure the machine is using the
same value.

S.M. HLF 1700 G1-F Eng V1-2017

14-15

HLF Italian Design

Summary of Contents for 1700




















































































































Search results

Summary of Contents for 1700

Reviews:

Related manuals for 1700

Brands by name

Popular brands

HLF Italian Design 1700, Service Manual

Search results

Summary of Contents for 1700

Reviews:

Related manuals for 1700

Brands by name

Popular brands