HLF Italian Design 1700 Service Manual Download Page 90

Page: 90 / 115

TROUBLESHOOTING

14.11 E39-COFFEE GROUP POSITIONING

Why?

The coffee group is moving. Wait for the completion of the movement.

Cause of fault

Troubleshooting measure(s)

The message stays still even if the
coffee group doesn’t move.

Maybe you’ve just put back the coffee
group. Remove the

white

door key

and

put it back, or close the

front door

14.12 E58-BOILER 1 PROBE OVER TEMPERATURE

Why?

The board is measuring a temperature above 120°C

Cause of fault

Troubleshooting measure(s)

The temperature probe got fault;

Replace it.

14.13 E59-BOILER 1 PROBE DISCONNECTED

Why?

The board is measuring a temperature below 0°C

Cause of fault

Troubleshooting measure(s)

The temperature probe is disconnected;

The temperature probe got fault.

Check the connections

Replace it.

HLF Italian Design

14-10

S.M. HLF 1700 G1-F Eng V0-2016

Summary of Contents for 1700




















































































































Search results

Summary of Contents for 1700

Reviews:

Related manuals for 1700

Brands by name

Popular brands

HLF Italian Design 1700, Service Manual

Search results

Summary of Contents for 1700

Reviews:

Related manuals for 1700

Brands by name

Popular brands