background image

--- 3 ---

(3) Higher durability thanks to the metallic bearing bushing

A metallic bearing bushing is built in and the outside is covered with resin tail cover for higher durability.

The resin tail cover secures the bearing bushing and also prevents the CB cap from loosening.

Bearing bushing (metal)

(4) Slip-resistant and comfortable soft grip handle

The grip of the Model WR 14VB is soft, slip-resistant and comfortable thanks to the soft material (elastomer

resin) covered on the handle.  The Model WR 14VB gives minimum fatigue to the operator's hand even if it is

operated for a long time.

(5) Housing is covered with elastomer entirely

The Model WR 14VB gives no scratch on the floor etc. where it is placed because the housing is covered with

elastomer entirely.  In addition, the elastomer-covered housing prevents the Model WR 14VB from slipping on

a slanted surface such as a roof.

(6) Steplessly variable speed trigger switch and speed change lever

The speed can be controlled by varying the amount that the trigger switch is pulled from 0 to 2,300 rpm

steplessly.  In addition, the speed change lever is selectable between high or low speed for the tightening

torque suitable for the operation.  (Refer to "6-2. Tightening Torque".)

(7) Grip end is shaped like a finger stopper for portability

The grip end is thickened to make it as a finger stopper for portability.

CB cap

Tail cover (resin)

Summary of Contents for WR 14VB































Reviews: