manualshive.com logo in svg

Hitachi WH 9DMR, Technical Data And Service Manual, Page: 22 / 47

Share
Download
Hitachi WH 9DMR Technical Data And Service Manual Download Page 22

--- 19 ---

 •

For safe operation, see Instruction Manual.

 •

Charge HITACHI charger recommended in

    instruction manual for recharging.

CAUTION

 •

Read thoroughly HANDLING INSTRUCTIONS

  before use.

(9) Do not attempt to disassemble the storage battery or the charger.

Special devices, such as a thermostat, are built into the storage battery and charger to permit rapid charging.

Incorrect parts replacement and/or wiring will cause malfunctions which could result in fire or other hazards.

Instruct the customer to bring these units to an authorized service center in the event repair or replacement is

necessary.

(10) Disposal of the Type EB 9B, EB 926H or EB 930H Storage Battery

Ensure that all customers understand that Type EB 9B, EB 926H or EB 930H Storage Batteries should be

turned into any Hitachi power tool sales outlet or authorized service center when they are no longer capable of

being recharged or repaired.  If  thrown into a fire, the batteries may explode, or if discarded indiscriminately,

leakage of the cadmium compound contained in the battery may cause environmental pollution.

B. Caution Plates

(1) The following precautions are listed on the Name Plate or Caution Plate attached to the main body of each

tool.

For the U.S.A. and Canada

For the U.S.A. (excludes French) or Canada

WARNING

 •

To reduce the risk of injury, user must read and understand

Instruction Manual.

AVERTISSEMENT

 •

Afin de réduire le risque de blessures, I'utilisateur doit lire

    et bien comprendre le mode d'emploi.

•

Read thoroughly HANDLING INSTRUCTIONS

  before use.   

•

Do not disassemble nor throw into fire.

CAUTION

For Oceania

(2) The following cautions are listed on the Name Plate attached to each type EB 9B, EB 926H or EB 930H

Storage Battery.

For Europe

CAUTION

Summary of Contents for WH 9DMR
















































Reviews:

No comments