manualshive.com logo in svg

Hitachi WH 9DMR, Technical Data And Service Manual, Page: 15 / 47

Share
Download
Hitachi WH 9DMR Technical Data And Service Manual Download Page 15

--- 12 ---

7-2. Specification Comparisons (Cordless Impact Wrench)

HITACHI

WR 9DMR

Maker

Model

Item

Catalog specifications

Capacity

M 6 --- M 14

(1/4" --- 9/16")

Ordinary bolt

120

(1220 kgf

•

cm, 1060 in-lbs.)

Max. tightening torque

N

•

m

0 --- 2,600

No-load rotation speed

/min

0 --- 3,200

Impact rate

/min

1.4 (3.0 lbs.)

 Main body weight

kg

118

(1200 kgf

•

cm, 1045 in-lbs.)

Max. tightening torque

N

•

m

Measured figures

0 --- 2,550

No-load rotation speed

/min

0 --- 3,440

Impact rate

/min

160 x 223

(6-19/64" x 8-25/32")

Overall length x height

mm

26.5 (1-3/64")

Center height

mm

1.43 (3.1 lbs.)

Main body weight

kg

70

No-load sound pressure level

dB(A)

Trigger switch with

forward/reverse

changeover pushing
button with brake and

variable

Type of switch

DC magnet

Type of motor

9.6

Voltage

29

Current

EB 9B, EB 926H or EB 930H

Battery

V

A

Type

EB 9B: 2.0

EB 926H: 2.6
EB 930H: 3.0

Nominal capacity

Ah

9.6

Nominal voltage

V

Ambient temperature

û

C

UC 14YFA or UC 18YG

Model

UC 14YFA: 56
UC 18YG: 70

Power input capacity

VA

UC 14YFA: 7.2 --- 14.4
UC 18YG: 7.2 --- 18

Recharging voltage

V

  

Plastic tool case

  

Charger (UC 14YFA

or UC 18YG)

Standard accessories

Charger

*

1

: Max. tightening torque is based on tightening an M12 (5/32") bolt (strength grade: 12.9) for 3 seconds with a hexagon

socket.

*

2

: Main body weight does not include accessory tools and hook (hexagon bit etc.).

*

1

*

2

*

1

*

2

WR 9DM2

M 6 --- M 14

(1/4 --- 9/16")

115

(1170 kgf

•

cm, 

1020 in-lbs.)

0 --- 2,600

0 --- 3,200

1.4 (3.0 lbs.)

122

(1240 kgf

•

cm, 1076 in-lbs.)

0 --- 2,460

0 --- 3,230

160 x 223

(6-19/64" x 8-25/32")

26.5 (1-3/64")

1.43 (3.1 lbs.)

70

Trigger switch with
forward/reverse

changeover pushing

button with brake and
variable

DC magnet

9.6

27

EB 9B or EB 930H

EB 9B: 2.0

EB 930H: 3.0

9.6

0 --- 40

UC 14YF2 or UC 14YFA

44 or 56

7.2 --- 14.4

  

Plastic tool case

  

Charger (UC 14YF2

   or UC 14YFA)

Retaining ring

Tool tip mounting system

Retaining ring

M 6 --- M 10

(1/4" --- 3/8")

High-strength bolt

M 6 --- M 10

(1/4" --- 3/8")

0 --- 40

9.5 mm (3/8") square drive

Tip condition

9.5 mm (3/8") square drive

Summary of Contents for WH 9DMR
















































Reviews:

No comments