manualshive.com logo in svg

Hitachi WH 9DMR, Technical Data And Service Manual, Page: 20 / 47

Share
Download
Hitachi WH 9DMR Technical Data And Service Manual Download Page 20

--- 17 ---

7-5. Number of Screws or Bolts Driven

Comparison data on the number of screws which can be tightened per battery charge are shown in the table

below.  Please note that the data below are intended for general reference only as the number of screws which

can be tightened per charge may vary depending on tightening conditions, screw sizes, ambient temperature,

characteristics of battery, etc.

(1) Screws (Cordless impact driver: Model WH 9DMR)

Battery

Tightening condition

Model

P

DW 9061

(Battery capacity: 1.7 Ah)

Wood screw
4.0 mm dia. and 50 mm length
Workpiece: Cedar, no prepared hole

260

690

Machine screw M8 x 16L

(2) Ordinary bolts (Cordless impact wrench: Model WR 9DMR)

Comparison data on the number of bolts which can be tightened per battery charge are shown in the table

below.  Please note that the data below are intended for general reference only as the number of bolts which

can be tightened per charge may vary depending on tightening conditions, bolt sizes, ambient temperature,

characteristics of battery, etc.

Battery

Tightening condition

Model

Coach bolt 9 x 90
Prepared hole
6.5 mm dia. and
90 mm depth

Number of bolts

Time (sec.)

HITACHI

WH 9DMR

EB 9B

(Battery capacity: 2.0 Ah)

260

690

HITACHI

WH 9DM2

EB 9B

(Battery capacity: 2.0 Ah)

233

753

HITACHI

WR 9DMR

EB 9B

(Battery capacity: 2.0 Ah)

27

15.4

HITACHI

WR 9DM2

EB 9B

(Battery capacity: 2.0 Ah)

29

13.4

Summary of Contents for WH 9DMR
















































Reviews:

No comments