Hitachi SJ100 Series Service Manual Download Page 17

Page: 17 / 75

(13) Over temperature (E 21)

Phenomena:

Temperature sensor which located close to IGBT inside ISPM shows a too high

temperature.

Cause:

Ventilator blocked. (for models which has ventilator.)

Remedy:

Check ventilator

Cause:

The frequency inverter does not get enough cooling air.

Remedy:

Check cabinet ventilation, air filters, and ventilation openings in the cabinet.

Way to Reset: A

(14) PTC error (E 35)

Phenomena:

Resistance of motor thermistor is high. This error can occur when you select

“PTC” function.

Cause:

Too much load of the motor.

Remedy:

Reduce the load, use bigger motor.

Cause:

Motor thermistor is not connected while PTC function is selected.

Remedy:

Disable PTC function when it is not used.

Cause:

Characteristics of the motor thermistor is not suitable. Frequency inverter gives
PTC error when the resistance value becomes more than 3k ohm +-10%.

Remedy:

Use motor which has suitable thermistor for the inverter.

Or change thermistor characteristics of the thermistor by debug mode.

Way to Reset:

Explanation of the way to reset.

A :

Make close the terminals between RS and P24 (CM1 only for Japanese version) on the I/O board, or

press “STOP/RESET” key of the operator.

3-6

Summary of Contents for SJ100 Series












































































Search results

Summary of Contents for SJ100 Series

Reviews:

Related manuals for SJ100 Series

Brands by name

Popular brands

Hitachi SJ100 Series, Service Manual

Search results

Summary of Contents for SJ100 Series

Reviews:

Related manuals for SJ100 Series

Brands by name

Popular brands