manualshive.com logo in svg

Hitachi Set Free mini-HNRQ1 Series, Installation & Maintenance Manual, Page: 33 / 52

Share
Download
Hitachi Set Free mini-HNRQ1 Series Installation & Maintenance Manual Download Page 33

29

4.7  Additional Refrigerant Charge Calculation

Although this unit has been charged with refrigerant, additional refrigerant charge is required on the site. 

Determine additional quantity of refrigerant required according to the following table, and charge it into the 

system.
(1) Calculating the method of Additional Refrigerant Charge

Model

Item

Contents

Total Additional 

Charge

RAS-

3.0~6.5

HNBRKQ1

For the refrigerant 
pipes

Liquid pipe 

diameter

Symbol

Total length of 

liquid piping

(m)

Refrigerant 

charge per meter

Additional 

charge

(kg)

W=W11+W12

+W13

Φ6.35

W11=

×0.020kg/m=

Φ9.52

W12=

×0.050kg/m=

Φ12.7

W13=

×0.085kg/m=

For the Indoor units

0

RAS-

7.0~12

HNBRMQ1

For the refrigerant 
pipes

Liquid pipe 

diameter

Symbol

Total length of 

liquid piping

(m)

Refrigerant 

charge per meter

Additional 

charge

(kg)

W=W11+W12

+W13+W21
+W22+W23

Φ6.35

W11=

×0.020kg/m=

Φ9.52

W12=

×0.059kg/m=

Φ12.7

W13=

×0.120kg/m=

For the 4-Way 
cassette indoor 
units

Model

Symbol

Numbers

(Q’ty)

Refrigerant 

charge per unit

Additional 

charge

(kg)

RCI-1.0~1.5

W21=

×0.23kg/pcs=

RCI-2.0~2.5

W22=

×0.29kg/pcs=

RCI-3.0~6.5

W23=

×0.47kg/pcs=

For the other indoor 
units

0

NOTE:

Ensure the total additional charge should not be exceeded the max. additional refrigerant charge quantity.

(2) Max. Additional Refrigerant Charge Quantity

Outdoor Unit

RAS-3.0~

3.5HNBRKQ1

RAS-4.0~

5.0HNBRKQ1

RAS-6.0~

6.5HNBRKQ1

RAS-7.0~

8.0HNBRMQ1

RAS-10~

12HNBRMQ1

Max. Additional Refrigerant Charge 
Quantity (kg)

3.9

7.9

8.6

12.9

12.9

(3) Refrigerant Charge Amount of Outdoor Unit before Shipment.

Outdoor Unit

W

0

(kg)

RAS-3.0~3.5HNBRKQ1

3.0

RAS-4.0~5.0HNBRKQ1

4.1

RAS-6.0~6.5HNBRKQ1

4.4

RAS-7.0~8.0HNBRMQ1

5.5

RAS-10~12HNBRMQ1

6.5

NOTE:

W

0

 is outdoor unit refrigerant charge before shipment.

(4) Record of Additional Charge

The total refrigerant charge of the system should be calculated by the following formula:

Total of Refrigerant Charge

=

W

+

W

0

The system

=

+

=

kg

Summary of Contents for Set Free mini-HNRQ1 Series





















































Reviews:

No comments