Non-water supply auto steamer [Plate and Inner Lid] (Wash after each use)
1
1
4
3
Cleaning and Maintenance - continued
2
6
5
Wash the plate to clean and unclog it.
Remove the non-water supply auto
steamer from the lid.
Separate the non-water supply auto steamer
into the inner lid and the other plate.
Wash the inner lid to clean and unclog it.
Attach the other plate to the inner lid.
Install the non-water supply auto steamer into
the lid.
●
The non-water supply auto steamer is assembled with the
inner lid and other plate.
●
Remove the steam cap from the lid and use dishwashing
detergent (pH-neutral) and a sponge or other soft material to
wash the steam cap.
The packing attached to the plate is not
removed, so do not pull on it. If the packing is
deformed, it will reduce the amount of water
that collects in the plate.
2.
While pushing the
release lever up, insert
the top side of the inner
lid.
3.
Lower the release lever.
To prevent cooking
when you have
forgotten to install the
non-water supply auto
steamer, the lid will not
close with a moderate
force.
(The lid closes when
there is no inner pot.)
1.
Orient the lid packing to
the front and insert the
hooks on both sides
into the groove.
If only the hook on one
side is inserted, that
hook could be damaged
when the inner lid is
closed.
Hold the lid knob while pushing the
release lever up and then remove the
non-water supply auto steamer.
Push down the plate lever and
remove the plate.
3.
3.
●
Clean the back of the regulator valve. Also remove the filter
and wash the front of the regulator valve. When the valve is
clogged with debris, use a cotton swab or similar item to
unclog it.
Regulator valve (Check before cooking)
Safety valve (Check before cooking)
●
If the safety valve (in the center) is clogged with rice or
debris, use a cotton swab or similar item to unclog it.
●
Use a cotton swab, etc. to press on the center of the safety
valve 2 or 3 times to confirm that it moves.
Filter (Wash after each use)
■
How to remove
the filter
Turn the filter
counterclockwise
and pull it forward.
■
How to install
the filter
Align the filter with
the
▲
mark, insert it,
and turn it clockwise
until it locks in place
and stops.
●
When the filter is clogged with rice or other debris, remove
and wash it. Make sure to put it back on after washing it.
●
As filter parts are very small, try not to lose them when
removing.
Remove
Vacuum valve (Wash after each use)
●
This is not removable, so do not pull it.
If it is deformed, the pressure cannot be
sustained and the rice will not cook well.
Inner lid and lid packing (Wash after each use)
●
Wash these together.
●
The lid packing is not detachable, so do not pull it. If it is
deformed, the pressure cannot be sustained and the rice
will not cook well.
●
Do not push on, pull on, or apply excessive
force to the pressure regulator. Failure to
observe this precaution could cause the rubber
part to come loose or tear, or damage the
device.
Steam sensor and pressure regulator
Note
Zapping sound
Lid knob
Re
eleas
ase lev
eve
ver
Le
Lev
eve
ver
Inner lid
Plat
ate
When installing the
filter, align it with the
▲
mark, and push it
clockwise
until it
stops.
Install
Do not remove the lid packing, regulator valve,
safety valve, or vacuum valve from the inner lid.
Do not install the plate upside down.
1.
Insert the bottom hook of the plate into the bottom guide at the
bottom of the inner lid.
2.
Align the hook at the top of the plate with the top guide and
press the plate in until you hear it lock in place.
Top hook
To
Top hook
k
Bottom hook
Bot
ott
ttom hook
id
Top guide
Top guide
g
To
Top guide
g
Bottom guide
Bottom guide
g
Bot
ott
ttom guide
2.
2.
30
31
Gr
Gr
Grooves
ooves
ooves
ooves
ooves
ooves
ᵏ
ᵏᵌ
㪈㪅
ᵏᵌ
㪈㪅
Summary of Contents for RZ-W2000YH
Page 1: ......
Page 31: ...㪉㪄㪣㪇㪌㪌㪌㪄㪈 㪝 ...
