
– 15 –
– 14 –
RAR-3R5
RAR-3R5
Select the operation mode.
Press the
(OPERA
TION
SELECT
OR) button.
•
Any one of Heating/Dehumidifying
/
Cooling/Dry Cool/Auto can be selected.
•
To
start fan operation, perform
stainless plasma air purifying
(F
AN) operation. (Page 18)
•
If the
(OPERA
TION SELECT
OR)
button is pressed during operation,
a double short beep is heard on auto
mode while a single short beep is
heard on other mode.
Set the fan speed.
Set the room temperature.
Set the humidity (only for
dehumidifying and dry cool modes).
Operation starts.
Press the
(ST
AR
T/ST
OP) button.
Press the
(ST
A
R
T
/ST
OP) button again.
•
A
short beep sounds and the operation stops.
•
From next time, the operation that has been set on the above procedure
①
-
④
can be performed just by pressing the
(ST
AR
T/ST
OP) button.
Humidity setting range
4
0-
70%
Remote controller temperature setting range
Heating, Cooling, Dry Cool
16
-3
2
°
C
Dehumidifying 10
-3
2
°
C
2
1
One of them lights up.
One of them lights up.
Press the
(HUMIDITY) button.
•
The humidity can be set in
increments of 5%.
•
Humidity indication disappears in
approximately 10 seconds if the
operation is not started.
Increase
Decrease
4
3
Lights up.
Lights up.
5
ST
OP
•
Outdoor temperature -20
°
C-2
1
°
C
(When it is below
-20
°
C
or over 24
°
C, the heating
function may not operate in order to protect the
device.)
Heating
Dehumidifying
D
ry Cool
Cooling
•
Outdoor temperature
1
°
C-3
5
°
C
(Operation does not start if the
room temperature is below 1
°
C. )
•
Outdoor
temperature
25
°
C-3
5
°
C
•
Outdoor
temperature
22
°
C-4
3
°
C
•
Do not use cooling operation in winter
.
Press the
(F
AN SPEED) button.
•
Any one of “AUT
O”, “HI”, “MED”,
“LOW”, “SILENT” can be selected.
Fan speed indication disappears
in approximately 10 seconds if the
operation is not started.
•
If the
(F
AN SPEED) button is
pressed during operation, a double
short beep is heard on auto mode
while a single short beep is heard
on other mode.
Press the
(ROOM
TEMPERA
TURE) button.
•
Room temperature indication
disappears in approximately 10 seconds
if the operation is not started.
•
If the
(ROOM TEMPERA
TURE)
button is pressed during operation,
a double short beep is heard at
20
°
C, a triple short beep at 30
°
C,
and a single short beep on other
temperature.
Increase
Decrease
Use the air conditioner following the operation conditions outlined below
.
MANUAL OPERATION (HEATING, DEHUMIDIFYING, COOLING, DRY COOL)
– 15 –
ENGLISH
(
(MIST/AIR
PURIFYING) indicators also
turn on during quick laundry
operation.)
Press the
(HEA
T) button to start heating operation.
3 types of dehumidifying operations can be performed by pressing the
(DEHUMIDIFY) button.
Performs powerful dry operation without lower down the room temperature.
Condensation
Control
•
In auto dehumidifying mode, fine adjustment of room temperature (page 13),
humidity adjustment and fan speed selection (page 14) can be made to your
preference.
Every time you press the ROOM
TEMPERA
TURE button, the temperature
will change by 1
°
C. (T
emperature setting range is not higher or lower than 3
°
C.) Every
time you press the HUMIDITY
button, the humidity will change by 5%. (Humidity setting
range is 40%
-70%.
)
•
In quick laundry mode, fine adjustment of room temperature (page 13) and fan
speed selection (page 14) can be made to your preference. (Fine adjustment of
room temperature and humidity adjustment cannot be made in condensation
control mode.)
Press the
(HEA
T) button.
•
Adjust the room temperature and fan speed to your preference.
T
emperature range between 16
°
C-3
2
°
C can be set. (Page 14)
Press the
(ST
A
R
T
/ST
OP) button.
•
A
short beep sounds and heating operation stops.
Press the
(DEHUMIDIFY) button.
•
Every time you press the
(DEHUMIDIFY) button, the
mode will change as shown in the chart below
.
Press the
(ST
A
R
T
/ST
OP) button.
•
A
short beep sounds and dehumidifying operation stops.
•
After the dehumidifying operation is stopped, the remote controller will display
the operation mode that had been set before the
(DEHUMIDIFY) button was
pressed.
(“AUT
O” flashes for 5 seconds)
Auto
Dehumidifying
Quick
Laundry
ST
OP
ST
OP
HEATING OPERATION
DEHUMIDIFYING OPERATION