– 14 –
– 12 –
RAR-3R5
1
While
(SA
VE) is blinking, point the remote controller towards
the unit and press the
(ON/OFF) button.
•
A
short beep sounds and
(SA
VE) indicator turns on.
Press the
(FUNCTION SELECT
OR)
button until
(SA
VE) blinks.
Press the
(FUNCTION SELECT
OR) button again until
(SA
VE) blinks.
While
(SA
VE) is blinking, point the remote controller towards
the unit and press the
(ON/OFF) button.
•
A
short beep sounds and
(SA
VE) indicator turns of
f, indicates
the setting is released.
Notes for “save” setting
•
If ampere is set to “Save”, the maximum heating capacity slightly lowers
and starting up of heating operation will take a little longer
. Besides,
the preset temperature may not be reached if outside temperature is
low
. (If ampere is set to
(SA
VE), the air conditioner will be in limited
operation at 6(A)).
•
Point the remote controller to the signal receiver of the unit
Signal reception distance is approximately 7m in front of the unit.
However
, this distance may be shorter or the signal may not be
receivable if there is an electronic lighting device in the same room.
•
Handle the remote controller with care
Dropping it or getting it wet may compromise its signal transmission
capability
.
After new batteries are inserted into the remote controller
,
the unit require approximately 10 seconds before it can respond to
commands and begin operation.
WHEN OPERA
TING THE REMOTE CONTROLLER
Approximately
7m from the front
Ampere setting (Standard/Save) can be selected.
If you experience frequent circuit breaker tripping, set ampere to “Save” to avoid this problem.
(Ampere is set to “Standard” at the time of purchase.)
4
2
RELEASE
PREPARE THE REMOTE CONTROLLER (continued)
– 13 –
ENGLISH
•
Performs heating operation when the room temperature is below 23
°
C.
Set the temperature to be around 23
°
C.
•
Performs dehumidifying operation when the room temperature is 23
-2
6
°
C.
The preset temperature will be the room temperature at the time of start of air conditioner
operation.
•
Performs cooling operation when the room temperature is above 27
°
C.
Set the temperature to be around 27
°
C.
RAR-3R5
RAR-3R5
Press the
(OPERA
TION SELECT
OR) button
to set the operation mode to auto.
•
Every time you press it, the mode will change as
shown in the chart on the right.
Press the
(ST
A
R
T
/ST
OP) button.
Based on the room temperature and outside temperature, the unit determines the most suitable operation
mode (heating, dehumidifying or cooling) and a comfortable temperature. (Set the current time on the remote
controller before starting operation.)
Press the
(ST
A
R
T
/ST
OP) button again.
•
A
short beep sounds and the automatic
operation stops.
•
Operation mode will be displayed on the
remote controller display
.
Adjust the room temperature
Press the
(ROOM
TEMPERA
TURE)
button.
•
Every time you press it, a short beep sounds and the
temperature will change by 1
°
C.
•
is displayed if the temperature is set higher than
the automatically set room temperature by 1
°
C.
is displayed if the temperature is set lower than the
automatically set room temperature by 1
°
C.
•
The adjustable temperature range is not higher or lower
than 3
°
C of the automatically set room temperature.
•
Humidity setting cannot be adjusted.
Increase
Decrease
B
eep
Room temperature and fan speed can be adjusted to your preference.
Select the fan speed
Press the
(F
AN SPEED) button.
•
“AUT
O”, “LOW” and “SILENT”
can be selected.
•
Every time you press it, the
mode will change as shown in
the chart on the right.
1
2
1
2
ST
OP
AUT
OMA
TIC OPERA
TION
Heating
Dehumidifying
Cooling
Even if dehumidifying operation is set, the air conditioner may not execute dehumidifying if the room humidity
is not very high.
This is not a malfunction.
AUTOMATIC OPERATION
