Hitachi R-S42CMJ, How To Use Manual

Page: 56 / 60

56
Flashing pattern Possible Cause Check Point
Food etc. may come in contact with the ice
tray or the stored ice amount detection lever.
This fl ashing shows that there is a problem.
It will fl ash if you stop ice making during the
ice making process.
Door remains open for more than 1 minute. (ex:
door is not completely closed.)
It is in process of Ice Maker Cleaning.
Empty the Ice Compartment and perform
"Cleaning the Ice Making".
Consult your dealer.
Check the points described in "Ice Tray" on
P.51.
Check the points described in "Door Alarm"
on P.57.
Check the points described in "How to
maintain the Automatic Ice Maker" on P.50.
" " fl ashing
3 times
" " fl ashing
(excluding fl ashing 3 times)
੄̥
(Stop)
fl ashing
All displays fl ashing
ݨఀყϕ
(Quick Ice
Making) , 製
ϕ
(Ice
Making) ,
੄̥
(Stop)
Flashing
Check
Ice making
function
PRACTICAL ADVICE ON HOW TO USE THE REFRIGERATOR/REPLACEMENT PARTS
REPLACEMENT PARTS
The " "
display fl ashes
on the Control
Panel for
operation
The electric
supply failed
The refrigerator
is not expected to
use for a long term
Moving house
Moving or carrying the refrigerator
Remove frost
When you want
to adjust the
temperature
more fi nely
● This fl ashing shows that there is a problem with the Automatic Ice Maker, the temperature control device or
the frost removal device etc.
● Consult your dealer if the fl ashing does not stop even after checking the point listed in the following table.
● Reduce the number of times of opening and closing the door and avoid storing food additionally until the
electric supply is restored.
● Unplug the power plug and maintain the inner of the refrigerator and the Automatic Ice Maker, and leave all
the door open to dry the refrigerator for 2 〜 3 days. Pg.47 〜 51
● Refer to When moving or carrying section. Pg.35
● Any operation to remove frost is not required because this refrigerator remove frost automatically.
Thawed water is collected in the evaporating tray and automatically evaporates.
When replacing the following parts, make sure to tell your dealer the type name and buy the special parts.
Replacing the water fi lter
● Replace the water fi lter when it becomes old.(Replace it normally once 3 〜 4 years.)
● Ordering the replacement water fi lter
Tell your dealer the parts number: RJK-30100 to buy the replacement water fi lter. (Ice making capacity is the same
with a water fi lter removed.)
Flashing
Temperature settings for Refrigerator and Freezer Compartments can be adjusted by nine
levels, more fi nely than the three levels:
ࣵ
(MIN) , 中 (MID) and 強 (MAX) .
1. Open the door of the Lower Freezer Compartment.
2. Push and hold the
冷藏
button on the Control Panel for fi ve seconds
or more until one beep sounds (This allows fi ner adjustment.)
3. Close the door of the Lower Freezer Compartment.
4. Adjust the 冷藏 or 冷凍 button to make an adjustment. The
temperature becomes higher by one level every time you push the button.
(Pushing
強 (MAX) returns to
ࣵ
(MIN) .)
5. If you want to stop the fi ne adjustment, perform the operation of 1 and 2.
Two beeps sound and you can set the temperature by normal step.
When you want to
lower the setting of
the condensation
prevention heater
(the partitioning iron
plates)
Partitioning
iron plates
Display ON
MIN MID MAX
Temperature setting
Lighting Blinking
઼
˛
ࣵ
●
A lower setting of the condensation prevention heater will reduce power consumption.
The setting of a heater for dew condensation prevention has four levels. The level 4 achieves the highest reduction in power consumption.
A lower setting of the condensation prevention heater may cause dew condensation in the partitioning iron
plates when humidity is high. When dew is formed, cancel the setting.
● The setting will be cancelled when the power plug is connected and disconnected or power failure recovery takes place.
● Setting the partitioning iron plate.
1. Open the door of the Lower Freezer Compartment.
2. With the door of the Refrigerator Compartment closed, push and hold the
冷凍 button on the control panel for 3 seconds or longer until one long
beep sounds (Level 1).
3. Repeat the procedure provided in Step 2 to change Energy Saving level further.
4. Close the door of the Lower Freezer Compartment.
To cancel the setting, perform the same operations at Level 1 and 2 under the
state of Level 4.
Alarm is raised (two beeps sound) to cancel the setting.
2 beeps
Level 1 for saving electricity Level 2 for saving electricity Level 4 for saving electricity Level 3 for saving electricity Deactivate
Long beep Long beep Long beep
Long beep
Long beep Long beep Long beep
Long beep
Long beep Long beep
Push this button for more
than 3 seconds
1 beep
Long beep
About 3
seconds