background image

PLANNING

GUIDE

Web: http://www.Dacor.com

Corporate Phone: 800-793-0093

Specifications are subject to change without notice.

See installation instructions for additional details.

11.14

42” and 48” Wide

Built-In Refrigerators

EF42DBSS, EF42NBSS, EF48DBSS, EF48NBSS, 

IF42DBOL, IF42NBOL, IF48DBOL, IF48NBOL

1/6

O

pening

 D

imensiOns

To avoid tipping during use, the solid soffit must be within 1” 

◊ 

(2.5 cm) maximum above the refrigerator. If the solid soffit 

is higher than 1” (2.5 cm) or one is not available, then the 

refrigerator must be braced. 

 

If the anti-tip boards are needed, they must be attached to the 

rear wall studs 80” to 90” (203 cm to 229 cm) above the floor. 

See installation instructions for more information. 

 

NOTE

: A clearance of ¹⁄

2

” (1.3 cm) must be maintained above 

the top grille in order for the top grille to be removed.

4"

(10.2 cm)

83

¹/

2

" (212.1 cm) min.

84

³/

4

" (215 cm) max.

to bottom of solid soffit

24"

(60.96 cm) min. 

77"

(196 cm)

A

Width

(see chart following)

Revised

04/22/08

"

(1.3 cm)

1

/

2

Model Series

Cutout Width A

EF42, IF42

41½” (105.4 cm) to 41¾” (106.1 cm)

EF48, IF48

47½” (120.7 cm) to 47¾” (121.3 cm)

NOTE

: Flooring under refrigerator must be at same level as the 

room. Face of cabinetry must be plumb.

A grounded 3 prong electrical outlet should be placed within 

◊ 

4” (10.2 cm) of the right side cabinets or end panel. See 

Electrical Requirements

 for more information.

The water shutoff should be located in the base cabinet on 

◊ 

either side of the refrigerator or some other easily accessible 

area. If the water shutoff valve is not in the cabinets, the 

plumbing for the water line can come through the floor or 

the back wall. See 

Water Supply Requirements

 for more 

information.

See Page 11.15

Summary of Contents for IF42 Series







Reviews: