Hitachi PV-XH850M User Manual Download Page 22 | Manualshive

Page: 22 / 31

background image

ENGLISH 23

Cleaning and maintenance

Turn off and unplug the appliance before cleaning.

Cleaning of the dust container

CAUTION:

Do not use benzene, solvents, abrasive cleaners, metal objects or

hard brushes to clean the appliance.

CAUTION:

Deformation may occur on the filters within time as a result of

usage. It shall be replaced with a new one to prevent loss of performance.

Contact with the customer services to buy a new one. (see P. 25)

Wipe the surface of the

body with a wet cloth (10).

Press the dust container lid

release button (12) to open

the dust container (11) and

discharge the dust collected

inside.

Push the trigger under the

appliance to clean the dust

container (11).

Detach the dust container

(11) from the body (10).

We recommend you to clean the dust container (11) after each operation.

«
...
20
21
22
23
24
...
»

Summary of Contents for PV-XH850M
































Reviews:

No comments

Related manuals for PV-XH850M

Brand: Midea Pages: 9

Brand: Numatic Pages: 20

Brand: Coway Pages: 124

Brand: Oreck Pages: 18

CENTURY 400 NMCU2250H

Brand: Ninja Pages: 50

Brand: Modd Pages: 13

Brand: Fein Pages: 350

Brand: LifeWise Pages: 2

Brand: RoboJet Pages: 42

Brand: Electrolux Pages: 16

Brand: Honeywell Pages: 20

Brand: Honeywell Pages: 27

Brand: Philips Pages: 6

Brand: Philips Pages: 2

Brand: Philips Pages: 6

Brand: Philips Pages: 6

Brand: Philips Pages: 6

Brand: Philips Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands