Hitachi PV-XH850M User Manual Download Page 24 | Manualshive

Page: 24 / 31

background image

ENGLISH 25

Cleaning and maintenance

Remove the metal filter and

inlet foam inside the dust

container (11) by rotating the

metal filter counterclockwise.

Install the inlet foam to the

metal filter.

Remove the inlet foam

inside the metal filter.

Install the metal filter and

inlet foam inside the dust

container (11) by rotating

the metal filter clockwise.

Remove the dust on the metal

filter and inlet foam by tapping

them to a hard surface such

as a waste bin or by using a

brush.

The metal filter and inlet foam shall be cleaned regularly.

Cleaning of the metal filter and inlet foam

«
...
22
23
24
25
26
...
»

Summary of Contents for PV-XH850M
































Reviews:

No comments

Related manuals for PV-XH850M

Brand: Makita Pages: 4

Brand: Daewoo Pages: 10

Brand: Fagor Pages: 14

Brand: Fagor Pages: 5

Brand: Hamilton Beach Pages: 2

Brand: AiroDoctor Pages: 8

G FORCE PRO VCEA23GPRBU

Brand: Gorenje Pages: 76

Brand: Pacific Pages: 7

Brand: Daewoo Pages: 38

Brand: Rowenta Pages: 8

Brand: Vytronix Pages: 12

STEAMTEC STEAMTEC 5 IH

Brand: Nilfisk-ALTO Pages: 72

Brand: CERCHIO Pages: 13

Brand: POLTI Pages: 6

PROHEAT ADVANCED

Brand: Bissell Pages: 2

Brand: Black+Decker Pages: 20

Brand: ShangFeng Pages: 26

Brand: Monster Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands