13
CONNECTION
Terminal Positions
Rear
q
Power Cord Socket
w
Aerial Socket
e
AV1
r
AV2
t
AV3
y
AV4
u
Monitor Out and Sub Woofer
i
Service use only
o
Power Swivel Terminal
(see
36
)
a
PC Connection terminals
(D-sub 15 pin and mini stereo for
Audio)
s
HDMI1, 2 and mini stereo for Audio
Side
d
AV5
f
Headphone input
g
Photo Input terminal
h
SD Memory Card slot
Connecting Procedure
This unit is ready for various kinds of connections. Make a connection in the following steps. Be sure to turn off the
Main Power fi rst when connecting external equipments.
1.
Connect Power Cord to the rear panel.
2.
Connect Aerial Lead.
3.
Connect your external equipments to the unit if any.
4.
Connect the Power Plug to the Wall Socket.
1.
Connecting Power Cord to the Rear Panel
Connect Power Cord to the monitor.
*Make sure not to connect the Power Plug to the Wall Socket
until all connections are completed.
2. Connecting Aerial Lead.
There are two ways to connect Aerial Lead.
q
When you do not have any other external equipment:
Connect the Aerial Lead directly into the Socket at rear panel.
w
When you have one or more external devices to connect:
1. Use RF cable to connect between each equipment and
Antenna.
2. Connect the Aerial Lead to an equipment‘In’Socket
marked
3. Connect the RF cable from the equipment ‘Out’ to the other equipment ‘In.’
4. Then, connect from the equipment ‘Out’ to “ANT” on the plasma screen Socket on marked
.
VCR
STB
IN
OUT
IN
OUT
OK
P
P
SD MEMORY
CARD
PUSH-EJECT
PH35814
INPUT(A
V5)
R
L/MONO
AUDIO
VIDEO
S-VIDEO
PH35826
Licensed by BBE Sound, Inc. under USP5510752 and 5736897.
BBE and BBE symbol are registered trademarks of BBE Sound, Inc.
WOW, SRS and symbol are trademarks of SRS Labs, Inc.
SERVICE USE ONLY
INPUT(RGB)
ANALOG RGB
INPUT(HDMI)
PC
AUDIO
AUDIO
A C
INPUT
(AV1)
INPUT
(AV2)
INPUT
(AV3)
INPUT
(AV4)
ANT
OUTPUT
AUDIO
AUDIO
AUDIO
AUDIO
AUDIO
L MONO
C
L MONO
C
L MONO
C
L
L
MONO
C
R
R
R
R
R
VIDEO
VIDEO
VIDEO
P
B
P
R
P
B
P
R
Y/VIDEO
Y/VIDEO
S-VIDEO
SUB
WOOFER
POWER SWIVEL
HDMI2
HDMI1
q
w
ert yu
i
o
a
s
h
g
f
d
[Example: Connecting Antenna
through STB and VCR]
Precautions when connecting the aerial
Please use a coaxial cable which is free from interference to connect the aerial. Avoid using a parallel fl at feeder
wire as interference may occur, causing reception to be unstable and stripe noise to appear on the screen.
Avoid using indoor aerial as this may be affected by interference. Please use CATV net or outdoor aerial.
For safety, install an external aerial conforming to AS1417.1 (applicable for Australia only)
If there are noise appearance in the picture of VHF-Low band channel, please use the double-shielded cable (not
provided) for RF LEADS to reduce the noise.
PW3-12th-P1-P24.indd 13
PW3-12th-P1-P24.indd 13
2005/11/09 9:48:20
2005/11/09 9:48:20
Summary of Contents for 42PD8800
Page 62: ...QR65402 Printed in Japan ...