Hitachi Solutions StarBoard FX-E90W User Manual Download | Manualshive

Page: 5 / 45

background image

4

StarBoard FX-E90W

Safe Handling

English

Safe Handling

Markings and Symbols

Various markings and symbols are used in this User's Guide and on this product, to ensure the
safe and correct use of this product and to prevent personal injury and property damage. These
symbols and their meanings are as explained below. Understand the information well before
reading the body of the User's Guide.

This is a Safety Warning symbol. This symbol will appear to raise

the attention of the user to existing risks that may cause harm to

people. To avoid any chances of injuries or possibly death,

DO NOT IGNORE the safety instructions that follow this symbol.

WARNINGS

This warning will appear where there exists a risk of death or fatal injuries.

CAUTIONS

This warning will appear where there exists a risk of moderate or light injuries.

NOTICE

This warning will appear where there exists a risk of damage to property.

This symbol draws attention to cautions (including warnings).

This symbol indicates something prohibited.

This symbol indicates something that must be done.

«
...
3
4
5
6
7
...
»

Summary of Contents for StarBoard FX-E90W














































Reviews:

No comments

Related manuals for StarBoard FX-E90W

Brand: PolyVision Pages: 63

Brand: Panasonic Pages: 6

StarBoard FX-DUO-63

Brand: Hitachi Pages: 48

Brand: Hitachi Pages: 46

Brand: Prima Pages: 27

Brand: Quartet Pages: 37

Brand: TZT USA Industries Pages: 13

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands