HISEER AS10S/L Operation Installation Maintenance Manual Download Page 50

Page: 50 / 67

Commissioning Form

Commissioning Form
Client / Installation address: Telephone

Number

Installer: Commissioned

Heat pump Model:

Heat pump serial number:

Commissioning date:

The heating system has been

lled and pressure tested

YES ( )

Expansion vessel for heating is sized,

tted & charged in accordance with manufacturer’s instructions

YES ( )

The heat pump is

tted on a solid/stable surface capable of taking its weight

YES ( )

The system has been

ushed and cleaned in accordance with heat pump manufacturer’s instructions

YES ( )

What system cleaner was used?

What inhibitor was used?

Qty:( ) litres

Are all exposed external pipeworks insulated?

YES ( )

Central heating mode ( 10 minutes after compressor start to run)

Is buffer tank installed

Capacity:( ) litres

Inlet

( )

℃

discharge

( )

℃

outlet

( )

℃

suction

( )

℃

ambient

( )

℃

HPS

( )

℃

Hot water

( )

℃

LPS

( )

℃

Power voltage

( )V

Current

( )A

Domestic hot water mode ( 10 minutes after compressor start to run)

Is a hot water cylinder installed Capacity:( ) litres Heating coil diameter ( )mm, length ( )m
Inlet

( )

℃

discharge

( )

℃

outlet

( )

℃

suction

( )

℃

ambient

( )

℃

HPS

( )

℃

hot water

( )

℃

LPS

( )

℃

Power voltage

( )V

Current

( )A

Additional heat sources connected: Gas Boiler ( ) Oil Boiler ( ) Electric Heater ( )
Solar Thermal ( )

YES ( )

The heating, hot water and ventilation systems complies with the appropriate Building Regulations

YES ( )

All electrical work complies with the appropriate Regulations

YES ( )

The heat pump and associated products have been installed and commissioned as the manufacturer’s
instructions

YES ( )

The operation of the heat pump and system controls have been demonstrated to the customer

YES ( )

The operation, installation and maintenance manual has been explained and left with the customer

YES ( )

Commissioning Engineer’s Signature

Customer’s Signature
(To con

rm demonstration of equipment and receipt of appliance instructions)

Commissioning Form

Summary of Contents for AS10S/L




































































Search results

Summary of Contents for AS10S/L

Reviews:

Brands by name

Popular brands

HISEER AS10S/L, Operation Installation Maintenance Manual

Search results

Summary of Contents for AS10S/L

Reviews:

Brands by name

Popular brands