manualshive.com logo in svg

HISEER AS10S/L, Operation Installation Maintenance Manual

Share
Download
HISEER AS10S/L Operation Installation Maintenance Manual Download Page 46

 

45

 
 

Access Manufacturer Level Parameter data   

 

 

Display Procedures 

press <Prg> to main menu, press Down 
button to Parameter, Press Enter button,   
Press Enter and 0 will flash, press Down 
button to the correct figure, press Enter to 
confirm. 
Likewise, change the other 3 figure .After 4 
correct figure are inputted, 
It will enter Service level parameter.   
If the inputted password is service, it will 
just enter Service level parameters. 
 
If the inputted password is manufacturer, it 
will access both service and manufacturer 
level parameter. 
press Down button to Manufacturer 
Parameter 

 
Press Down button, it display parameter and 
data. 
Press Enter to confirm, 
when data is flashing, press Up or Down 
button to change the value. 
Press Enter to confirm.   
Cursor will move to P02 
When P02 is flashing, press Down button to 
next parameters. 

Or, continuously press <Esc> to exit out of the current level and back to the desired 
menu level. 

 

 

Warning : Manufacturer parameter is related to the unit safe running and reliability. It is not 
supposed to be changed without manufacturer’s permission. Any wrong change could possibly 
cause the unit broken. 
 
 
 
 
 
 
 
 
 
 
 
 
 

Manufacturer parameters 

Summary of Contents for AS10S/L




































































Reviews:

No comments

Brands by name

Popular brands

Load more brands