background image

 

PRS 80 Wind Speed Operator’s/Service Manual 

© Hirschmann ECS, 2006; PRS 80 Wind Speed Rev.C  05/23/06 

190184_C 

 

NOTICE 

 
Hirschmann ECS makes no warranty of any kind with regard to this material, including, but not limited 
to, the implied warranties of merchantability and/or its fitness for a particular purpose. 
 
Hirschmann ECS will not be liable for errors contained in this manual or for incidental or consequential 
damages in connection with the furnishing, performance, or use of this manual. This document 
contains proprietary information, which is protected by copyright, and all rights are reserved.  
 
No part of this document may be photocopied, reproduced, or translated to another language without 
the prior written consent of Hirschmann ECS. 
 
Hirschmann ECS reserves proprietary rights to all drawings, photos and the data contained therein. 
The drawings, photos and data are confidential and cannot be used or reproduced without the written 
consent of Hirschmann ECS. The drawings and/or photos are subject to technical modification without 
prior notice. 
 
All information in this document is subject to change without notice. 
 
 
 

MANUAL REVISIONS 
 

REV  DATE 

NAME 

DESCRIPTION 

- 02/04/05 CSH 

ECN 

04-152 

A 06/17/05  SB ECN 

05-109 

B 08/19/05  SB ECN 

05-150 

C 05/23/06  SB ECN 

06-096 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Summary of Contents for PRS 80 Wind Speed
























Reviews: