background image

en

FCC statement / IC statement

-CAUTION-
This equipment has been tested and found to comply
with the limits for a class B digital device, pursuant to
part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interfer-
ence in a residential installation. This equipment gener-
ates, uses, and can radiate radiofrequency energy and,
if not installed and used in accordance with the instruc-
tions, may cause harmful interference to radio com-
munications.

However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does
cause harmful interference to radio or television recep-
tion, which can be determined by turning the equipment
on and off, the user is encouraged to try to correct the
interference by one or more of the following measures:

• Re-orient or re-locate the receiving antenna.
• Increase the distance between the equipment and

receiver.

• Connect the equipment to an outlet on a circuit differ-

ent from that to which the receiver is connected.

• Consult the dealer or an experienced TV/radio techni-

cian for assistance.

-NOTE-
Changes or modifications not expressly approved by
the party responsible for compliance could void the user’s
authority to operate the equipment. 

This device complies with part 15 of the FCC Rules.

Operation is subject to the following two conditions:

1) this device may not cause harmful interference, and
2) this device must accept any interference received,

including interference that may cause undesired oper-
ation.

This device complies with the requirements defined in
RSS-210 of IC.

Operation is subject to the following two conditions:

1) this device may not cause harmful interference, and
2) this device must accept any interference received,

including interference that may cause undesired oper-
ation.

Printed: 07.07.2013 | Doc-Nr: PUB / 5136621 / 000 / 00

Summary of Contents for PX 10
















Reviews: