background image

Fault

Possible cause

Remedy

The receiver is switched on but

no signal is indicated on the

display.

The signal is screened by sheet

metal.

If possible, make the measurements

at an area where there is no sheet

metal.

The transmitter cannot be

switched on or switches itself

off after a short time.

The battery is dead.

Change the transmitter battery.

The receiver cannot be

switched on or switches itself

off after a short time.

The battery is dead.

Change the receiver battery.

Measurements are inaccurate.

The influence exerted by metal is too

strong.

Check accuracy by making measure-

ments “in the air” or on a wall con-

taining no steel reinforcement.

The tool is faulty.

Have the tool checked at a Hilti ser-

vice center if the measuring tolerance

is exceeded.

The direction indicator arrows

flicker at random.

Microphonia effect due to strong vi-

bration of the receiver.

Keep the receiver steady.

Interference fields, e.g. caused by

cordless telephones, switched-on

computer screens etc.

Switch off the source of all interfer-

ence fields.

The adhesive putty doesn’t hold

properly.

The adhesive putty has been used too

often.

Use new adhesive putty.

The contact surfaces are not clean.

Clean the contact surfaces.

10 Disposal

CAUTION

Improper disposal of the equipment may have serious consequences: The burning of plastic components generates

toxic fumes which may present a health hazard. Batteries may explode if damaged or exposed to very high

temperatures, causing poisoning, burns, acid burns or environmental pollution. Careless disposal may permit

unauthorized and improper use of the equipment. This may result in serious personal injury, injury to third parties and

pollution of the environment.

Most of the materials from which Hilti tools and appliances are manufactured can be recycled. The materials must

be correctly separated before they can be recycled. In many countries, Hilti has already made arrangements for

taking back old tools and appliances for recycling. Ask Hilti customer service or your Hilti representative for further

information.

For EC countries only
Disposal of electric tools together with household waste is not permissible.
In observance of European Directive 2002/96/EC on waste electrical and electronic equipment and its

implementation in accordance with national law, electric tools that have reached the end of their life

must be collected separately and returned to an environmentally compatible recycling facility.
Dispose of the batteries in accordance with national regulations.

en

17

Printed: 07.07.2013 | Doc-Nr: PUB / 5136621 / 000 / 00

Summary of Contents for PX 10
















Reviews: