![background image](http://html.mh-extra.com/html/hilti/ag-125-7se/ag-125-7se_original-operating-instructions_2135560032.webp)
24
English
6. Press the spindle lockbutton and hold it in this position.
7. Use the pin wrench to tighten the clamping nut securely, then release the spindle lockbutton and remove
the wrench.
6.5.2 Removing the grinding disc
1. Disconnect the mains plug from the power outlet.
CAUTION
Risk of breakage and irreparable damage.
If the spindle lockbutton is pressed while the spindle is
rotating, this may cause the accessory tool to work loose or detach from the power tool.
▶
Press the spindle lockbutton only when the spindle has stopped rotating.
2. Press the spindle lockbutton and hold it in this position.
3. Release the clamping nut by gripping it with the pin wrench and turning the nut counterclockwise.
4. Release the spindle lockbutton and remove the grinding disc.
6.6 Fitting the wire brush
9
1. Disconnect the mains plug from the power outlet.
2. Fit the side handle. → page 22
3. Fit the guard. → page 23
4. Place the wire brush in position and tighten it hand-tight.
5. Press the spindle lockbutton and hold it in this position.
6. Tighten the wire brush with a suitable open-end wrench.
7. Then release the spindle lockbutton and remove the open-end wrench.
6.7 Fitting the abrasive resin-fiber disc
10
1. Disconnect the mains plug from the power outlet.
2. Fit the side handle. → page 22
3. Fit the guard. → page 23
4. Fit the support plate and the abrasive resin-fiber disc, screw on the clamping nut and tighten it securely.
5. Press the spindle lockbutton and hold it in this position.
6. Use the pin wrench to tighten the clamping nut securely, then release the spindle lockbutton and remove
the wrench.
6.8 Types of work
WARNING
Damaged power cords are a safety hazard!
If the supply cord or extension cord is damaged while
work is in progress, immediately disconnect the device and the cord from the electricity supply. Do
not touch the damaged part of the cord.
▶
Regularly check all supply cords. Replace defective extension cords. Have damaged power cords
replaced by a qualified specialist.
Use of a ground fault circuit interrupter (residual current device, RCD) with a maximum tripping current of
30 mA is recommended.
6.9 Switching on
1. Plug the supply cord into the power outlet.
2. Press the rear section of the on/off switch.
3. Slide the on/off switch forward.
4. Lock the on/off switch.
◁
The motor runs.
Printed: 08.09.2017 | Doc-Nr: PUB / 5373395 / 000 / 00
Summary of Contents for AG 125-7SE
