hilscher COMX 100CA-DN Design Manual Download Page 3

Page: 3 / 78

Introduction

3/78

3.4.2

Diagnostic Interface USB ................................................................................................................ 63

3.5

SYNC Signals ..............................................................................................................................66

Technical Data ......................................................................................................................................67

4.1

Product Tests ...............................................................................................................................68

4.1.1

COMX 10CA-CCS........................................................................................................................... 68

4.1.2

COMX 10CN-CCS........................................................................................................................... 68

4.1.3

COMX 10CA-COS........................................................................................................................... 68

4.1.4

COMX 10CN-COS .......................................................................................................................... 69

4.1.5

COMX 10CA-DPS ........................................................................................................................... 69

4.1.6

COMX 10CN-DPS........................................................................................................................... 69

4.1.7

COMX 10CA-DNS........................................................................................................................... 70

4.1.8

COMX 10CN-DNS........................................................................................................................... 70

4.1.9

COMX 50CA-REFO ........................................................................................................................ 70

4.1.10

COMX 50CA-CCS........................................................................................................................... 71

4.1.11

COMX 51CA-RE ............................................................................................................................. 71

4.1.12

COMX 100CA-CO ........................................................................................................................... 71

4.1.13

COMX 100CA-DN ........................................................................................................................... 72

4.1.14

COMX 100CA-DP ........................................................................................................................... 72

4.1.15

COMX 100CA-RE ........................................................................................................................... 72

4.1.16

COMX 100CN-CO........................................................................................................................... 73

4.1.17

COMX 100CN-DN ........................................................................................................................... 73

4.1.18

COMX 100CN-DP ........................................................................................................................... 74

4.1.19

COMX 100CN-RE ........................................................................................................................... 74

Appendix ...............................................................................................................................................75

5.1

List of Tables................................................................................................................................75

5.2

List of Figures...............................................................................................................................77

5.3

Contacts .......................................................................................................................................78

Summary of Contents for COMX 100CA-DN















































































Search results

Summary of Contents for COMX 100CA-DN

Reviews:

Related manuals for COMX 100CA-DN

Brands by name

Popular brands

hilscher COMX 100CA-DN, Design Manual

Search results

Summary of Contents for COMX 100CA-DN

Reviews:

Related manuals for COMX 100CA-DN

Brands by name

Popular brands