Hill-Rom Itegris 2001B Installation Instructions Manual Download Page 4

Page ii

is444re

October 13, 2003

08/27/03 DRAFT

© 2003 by Hill-Rom Services, Inc. ALL RIGHTS RESERVED.

No part of this text shall be reproduced or transmitted in any form or by any 
means, electronic or mechanical, including photocopying, recording, or by any 
information or retrieval system without written permission from Hill-Rom 
Services, Inc. (Hill-Rom).

The information in this document is confidential and may not be disclosed to 
third parties without the prior written consent of Hill-Rom.

Sixth Edition

First Printing 2000

Printed in the USA

E-Z Ancor® is a registered trademark of Illinois Tool Works, Inc.

Hill-Rom® is a registered trademark of Hill-Rom Services, Inc.

Integris® is a registered trademark of Hill-Rom Services, Inc.

National Electrical Code® is a registered trademark of National Fire Protection 
Association, Inc.

NEC® is a registered trademark of National Fire Protection Association, Inc.

The information contained in this document is subject to change without 
notice. Hill-Rom makes no commitment to update or keep current, the 
information contained in this manual.

The only product warranty intended by Hill-Rom is the express, written 
warranty accompanying the bill of sale to the original purchaser. Hill-Rom 
makes no other warranty, express or implied, and in particular, makes no 
warranty of merchantability or fitness for a particular purpose.

Additional copies of this document can be obtained from Hill-Rom.

Summary of Contents for Itegris 2001B































Reviews: